Best Cooling Block 1080

The glacier G1080 founders Edition is made from premium materials and finest standards of craftsmanship from Phanteks. From military standard Viton O-ring to the RGB LED lighting, all of our exceptionally high-quality materials are carefully selected. The water block features a nickel-plated copper cold plate, Acrylic top and sandblasted cover plates for an elegant look. Glacier G1080 founders Edition is a full cover water block. The G1080 founders Edition water block covers the entire PCB of the card allowing the graphics card and its VRM to remain cool and stable. The G1080 founders Edition water block has a 9mm copper base for higher level of heat dissipation and heat transfer. The sealing is ensured by DuPont Viton rubber washers. The military-grade Viton increase temperature capability and stands up to aggressive fluids. The Viton rubber washers offers ruggedness so seals and components resist damage during installation and use. The Viton retains sealing force to prevent leaks even after compression for long periods. Glacier G1080 founders Edition uses the same RGB connector as our Phanteks cases so installation will be a breeze. With the RGB control of our compatible Phanteks cases, the G1080 founders Edition can synchronize with the case. Use the included RGB adapter (ph-cb4rgb) and you can sync with motherboards’ that support the 4pin RGB header including the ROG aura/MSI mystic light. The water block features a connection terminal that has a significantly Reduced flow resistance for an outstanding cooling performance.

Quickly mount any Kraken Series liquid cooler onto graphics cards with the Kraken G12 mounting kit. It delivers a 40% increase in cooling capacity over stock cooling, and features a newly designed bracket with an easier installation process versus the Kraken G10. Plus, the G12 is compatible with more than 30 liquid coolers on the market.

Compatibility – Graphic Cards
Nvidia
Titan X, Titan, Geforce GTX 1080 Ti, 1080, 1070, 1060, 980 Ti, 980, 970, 960, 780 Ti, 780, 770, 760, 680, 670, 660Ti, 660, 580, 570
\AMD
RX 480, 470, R9 390X*, 390*, 380X*, 380, 290X*, 290*, 285*, 280X*, 280*, 270X, 270, R7 370, HD7970*, 7950*, 7870, 7850, 6970, 6950, 6870, 6850, 6790, 6770, 5870, 5850, 5830
* Some variations in AMD die height may require the use of a copper shim which is not included.

Compatibility – AIO Liquid Coolers
NZXT
Kraken X72, X62, X52, X42, X61, X41, X31, X60, X40

Corsair
H105, H110, H90, H75, H55, H50 (CW-906006-WW only)

Thermaltake
Water 3.0 Riing RGB 360, 280, 240, Red 280, 140,
Water 3.0 Ultimate, Extreme S, Extreme, Pro, Performer
Water 2.0 Extreme, Pro, Performer

Antec
KUHLER H2O 920V4, 620V4, 920, 620

Zalman
LQ-320, LQ-315, LQ-310

The Corsair Hydro x series XG7 20-series GPU water block is a total conversion copper water block for your NVIDIA GeForce RTX 2080 Ti graphics card. Precision CNC-milled nickel-plated copper construction and more than 50 high-density cooling fins positioned over the GPU maximize thermal transfer and Surface area, for dramatically lower temperatures and maximum performance. A fully transparent flow path and discrete RGB lighting puts your graphics card on full display, When combined with a Corsair lighting Node Pro or Commander Pro and Corsair CUE software. A full-length aluminum casing and included backplate encloses all your graphics card’s critical components for a total conversion to custom cooling. With pre-applied thermal material, standard G1/4” threads and easy to follow step-by-step instructions, it’s never been easier to unlock the true potential of your NVIDIA GeForce RTX 2080 Ti. Tech Support # 1-888-222-4346 opt # 1. Operating Temperature : 60°C coolant temperature

EK-FC1080 GTX Ti FTW3 RGB is a high-performance full-cover water block for EVGA GeForce GTX 1080 Ti FTW3 based graphics cards, based on NVIDIA Pascal architecture (GP102). The water block comes with pre-installed 4-pin 12V RGB LED strip. This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it’s VRM to remain stable under high overclocks. EK-FC1080 GTX Ti FTW3 RGB water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps. The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. The sealing is ensured by quality rubber O-rings. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 4-pin LED connector is to be aligned with the +12V marking on the RGB header. EKWB recommends the purchase of aesthetic retention backplate which improves the looks of your graphics cards and also provides some passive cooling to the circuit board VRM section. The EK-FC1080 GTX Ti FTW3 RGB water block is compatible with EK-FC1080 GTX Ti FTW3 Backplates and the factory EVGA backplate as well.

Model: 3830046996466

Backplate is just for showcase and it is not included! This product should NOT be installed with any aluminum Fluid Gaming parts EK-FC1080 GTX Ti TF6 is a high-performance full-cover water block for MSI GEFORCE GTX 1080 Ti based graphics cards, based on NVIDIA Pascal architecture (GP102). Please check our Cooling Configurator online compatibility system for detailed compatibility list! This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it’s VRM to remain stable under high overclocks. EK-FC1080 GTX Ti TF6 water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps. The top also features two pre-drilled slots for 3mm diodes. The sealing is ensured by quality rubber washers. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure. The factory backplate of the MSI GeForce GTX 1080 Ti Gaming 11G and MSI GeForce GTX 1080 Ti Gaming X 11G graphics cards is compatible with this water block. G1/4″ threaded fittings can be used on both sides of the FC terminal. Up to four EK-FC1080 GTX Ti TF6 water blocks can be used on a single ATX form factor motherboard by using EK-FC Terminal (DUAL, TRIPLE or QUAD type) system or other means of interconnectivity. Please note that the old EK-FC Bridge & Link system is not compatible with this water block.

The Corsair Hydro x series XC7 RGB CPU water block combines premium construction, vivid RGB lighting and extreme cooling performance. A precision machined nickel-plated copper cold plate and more 60 high-efficiency micro-cooling fins draw the maximum amount of heat from your CPU, dropping temperatures and letting you push your clock speeds to their maximum. A transparent flow chamber shows off your coolant in all its glory, lit by 16 individually addressable RGB LEDs for 360° of customizable RGB lighting, controlled by adding a Corsair lighting Node Pro or Commander Pro. Powered by Corsair iCUE software to deliver nearly limitless lighting customization and control, the XC7 is ready to become to become the centerpiece of your custom cooling system. Tech Support # 1-888-222-4346 opt #1

Type: Water Cooling Compatible CPU: Intel / AMD Material: Acrylic/ Red copper/ Steel Base Size(L x W x H): 10. 5×5. 2×1. 5cm/ 4″x2. 2″x0. 5″ approx. Connector: 10mm/ G1/4″ diameter Color: Black Weight: 160g

The EK-FC1080 GTX Ti Strix RGB is a high-performance full-cover water block for all ASUS ROG Strix GeForce GTX 1080 Ti graphics cards versions on the market! The water block comes with pre-installed 4-pin 12V RGB LED strip. This water block directly cools the GPU, RAM, and VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it’s VRM to remain stable under high overclocks. EK-FC1080 GTX Ti Strix RGB water block features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. Moreover, such design offers great hydraulic performance allowing this product to be used in liquid cooling systems using weaker water pumps. The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. The sealing is ensured by quality rubber O-rings. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure.

Model: 3830046995698

The Alphacool XPX Eisblock is the newest generation in the CPU watercooling field and offers not only outstanding cooling performance but also many ways to customize your cooler. The mounting bracket, the aluminium cap, and even the logo can all be switched out for different colour variants. The Alphacool Eisblock XPX cooler is the newest innovation in the CPU cooler field, developed by Alphacool. The XPX cooler’s performance has gotten a major upgrade compared to its predecessor, the NexXxoS XP3. This was only possible because Alphacool completely re-developed the Eisblock XPX cooler from the ground up. For one, the fin structure was refined to 0.2mm and the fin count raised to 81 fins. This makes for a much larger cooling surface through which water can flow. In order to ensure the water is evenly distributed over the cooling fins, Alphacool developed and patented the “Ramp”. It ensures there is no turbulence in the water flow over cooling fins, which would lead to uneven water distribution over the cooling fins. Alphacool also used a double distributor to ensure less resistance. Paired with the ramp, this means the pump pressure plays little to no role in the performance of the cooler. You can turn the pump power down and run your system even more quietly without losing any cooling power. The bottom area of the XPX Eisblock has been optimized for CPUs with large DIE, as the cooling surface onto which the water actually flows was enlarged to 34 x 32mm, meaning even large 10 core CPUs present no problem. The bracket was also adjusted and simplified. This means new brackets for any socket type can be produced easily if required later. The aluminium frames also come in the same colours as the cooler itself. Alphacool has catered to users looking for customized design options, since the aluminium body which covers the entire cooler can be switched out for other models in different colours. Even the mounting kit can be colour-coordinated.

Model: 12588

Conclusion

By our suggestions above, we hope that you can found cooling block 1080 for you.Please don’t forget to share your experience by comment in this post. Thank you!