The 9 Best Phobya Water Cooling

The new temperature sensor from Phobya with g1/4″ inner thread and G1/4″ outer thread respectively. With its compact design this sensor can be integrated into the cooling loop at virtually any suitable thread. Its timeless design makes it blend right into the system, especially as it’s low height of only 11,6mm (without threads) allows it to fit below almost any connector. The sensor cable is equipped with a standard 2-Pin plug. High-Flow, no narrowing of the cooling channel inside of the sensor! Also see example of installation. This cable is not only practical, it is also optically appealing, The surrounding mesh, also called mesh, which is surrounding the cable itself offers the advantages that every Pro-modder is looking for: A completely unique look, even of the cables in the system! Special attention was paid to the combination of cable connectors, sleeve and heatshrink which were used to ensure great design and a unique as well as elegant look.

Model: 71227

Another innovative component for your watercooling system by Phobya! The newest innovations combined with exclusive appearance and proven functionality. The top and bottom are made from solid metal and combined with a transparent tube made from Plexi. The reservoir is shipped with two black mounts with safety latch. These mounting clips have a foam plastic sheet at their inside to protect the Plexi of the reservoir. Versatility and functionality were a great factor when designing this reservoir. You will notice the large number of connection threads, two at the bottom and two at the side of the bottom piece, which allows a great variety of mounting possibilities. The threads at the side especially make horizontal installation of the reservoir easily possible, giving you a whole array of new possibilities. The fifth connection thread in the top piece can be used as an In- our outlet when installed horizontally or for connection of a Fillport etc. Another possibility is to equip the unused threads with lighting modules to shine a whole new light on your reservoir! An ”Anti-cyclone” was integrated. This separating plate prevents vortexing inside of the reservoir and also prevents stronger pumps to suck in air bubbles from the inlet. All connection threads in the reservoir are 1/4″ in size. Thee nickel plated screw plugs are included for the unused threads. Both bottom and top piece may be removed for cleaning of the tube. All mounting material is also included! Note: The outer diameter is 50mm, the inner diameter is 40mm. So the thickness of the wall is 5mm. The thread M42x1.5.

Model: 45153

Highly precise In-line temperature sensor for almost all G1/4″ threads. The sensor can be integrated at any point in the cooling loop. At the measuring point the wall thickness of the casing is reduced to <1mm and="" the="" sensor="" is="" insulated="" from="" the="" outside="" to="" allow="" maximum="" precision="" and="" quick="" reaction="" of="" the="" measurement.="" due="" to="" its="" inner="" diameter="" of="" 1cm="" this="" sensor="" adds="" no="" restriction="" compared="" to="" fittings="" and="" small="" to="" medium="" sized="" tubing.="" therefore="" this="" sensor="" is="" truly="" ''high-flow="" capable".="" this="" cable="" is="" not="" only="" practical,="" it="" is="" also="" optically="" appealing,="" the="" surrounding="" mesh,="" also="" called="" mesh,="" which="" is="" surrounding="" the="" cable="" itself="" offers="" the="" advantages="" that="" every="" pro-modder="" is="" looking="" for:="" a="" completely="" unique="" look,="" even="" of="" the="" cables="" in="" the="" system!="" special="" attention="" was="" paid="" to="" the="" combination="" of="" cable="" connectors,="" sleeve="" and="" heatshrink="" which="" were="" used="" to="" ensure="" great="" design="" and="" a="" unique="" as="" well="" as="" elegant="">

Model: 71225

Another innovative component for your watercooling system by Phobya! The newest innovations combined with exclusive appearance and proven functionality. The top and bottom are made from solid metal and combined with a transparent tube made from Plexi. The reservoir is shipped with two black mounts with safety latch. These mounting clips have a foam plastic sheet at their inside to protect the Plexi of the reservoir. Versatility and functionality were a great factor when designing this reservoir. You will notice the large number of connection threads, two at the bottom and two at the side of the bottom piece, which allows a great variety of mounting possibilities. The threads at the side especially make horizontal installation of the reservoir easily possible, giving you a whole array of new possibilities. The fifth connection thread in the top piece can be used as an In- our outlet when installed horizontally or for connection of a Fillport etc. Another possibility is to equip the unused threads with lighting modules to shine a whole new light on your reservoir! An ”Anti-cyclone” was integrated. This separating plate prevents vortexing inside of the reservoir and also prevents stronger pumps to suck in air bubbles from the inlet. All connection threads in the reservoir are 1/4″ in size. Thee nickel plated screw plugs are included for the unused threads. Both bottom and top piece may be removed for cleaning of the tube. All mounting material is also included! Note: The outer diameter is 50mm, the inner diameter is 40mm. So the thickness of the wall is 5mm. The thread M42x1.5.

Model: 45151

This product perfectly combines all the requirements from different watercooling users: Quiet: At less than 22dB even most fans in the system emit more noise. For decoupling and therefore further noise reduction two kits are included with the pump: The first a map for quick and easy mounting on the case floor. The mat is self-adhesive on both sides and therefore reliably fixates the pump. The second possibility for pump installation are two brackets with which the pump can be fixated in the case. A ceramic-based centrifugal bearing promises quiet operation and a long lifespan. Compact: With the small outer dimensions (see technical specifications) the pump can be installed in almost any corner of the case, even in Midi- or Mini-towers. The compact dimensions of the pump also make connection to the cooling loop easy as the pump’s position can easily be varied. Powerful: Such a small and quiet pump so far always required compromises regarding the power. Not anymore! 2.6m of pressure head and 600l/h of flow are the kind of performance that will not be stopped even by cooling loops even with multiple waterblocks. G1/4″ connection: No adaptors, no annoyingly long connectors any more! Simply screw in the desired connector and you are set to go! 12V connector: The first advantage of a 12V connector is that it makes the connection with a 230V cable obsolete and that internal operation is made safe and easy. The other great feature of this pump is the connector: It is not a standard 4-Pin Molex connector, it is a 4-Pin PWM connector. This pump can therefore be operated at a fan connector on a Mainboard or a fan controller. This also allows a speed reduction of the pump: Only 8V are required for starting and operation of the pump which makes it additionally quiet and smooth in operation. The fan connector also offers the advantage of rpm monitoring with a compatible controller.

Model: 49137

Hose clamp for fixation of tubing on barbed fittings without union nuts.

The great advantage of barbed fittings is the larger inner diameter compared to compression fittings. Only the lack of additional fixation was a problem. But now these all-new hose clamps provide an optically appealing solution to the issue. Easy to install with a hexagonal socket screw, available in many colors and functional at the same time – the ultimate hose clamp!

Technical specifications:
Material: Black anodized Aluminum
Color: Black
Compatible inner diameter: 10mm to 11mm (3/8″ to 7/16″)

Please note: Should you use the hose clamps on barbed fittings, please note that the fittings will widen the outer diameter of the tubing by 1-2mm (depending on the wall thickness)

Model: TR-68118-4P

The new pumps by phobya stir up the watercooling market! Very quiet, extremely powerful, compact and with a long lifespan: This is the first pump generation by Phobya. Especially when considering the price this pump is truly a great option for your watercooling system! The continuously growing portfolio of accessories additionally increases the possibilities of use and mounting varieties!

Model: 49095

This special pad prevents damages and chipping or shorts and fits on all Chips without a protective frame with an open Core. The special feature of this pad is that it additionally features great thermal conductivity unlike other protective pads. Provides the following benefits: Open Cores are protected, Mounting of coolers/ waterblocks is made easier and safer, Electrical non-conductivity prevents shorts, and Thermal conductivity optimizes cooling of the Chip

Model: 31059

Hose clamp for fixation of tubing on barbed fittings without union nuts.

The great advantage of barbed fittings is the larger inner diameter compared to compression fittings. Only the lack of additional fixation was a problem. But now these all-new hose clamps provide an optically appealing solution to the issue. Easy to install with a hexagonal socket screw, available in many colors and functional at the same time – the ultimate hose clamp!

Technical specifications:
Material: Blue anodized Aluminum
Color: Blue
Compatible inner diameter: 13mm to 14.3mm (1/2″)

Please note: Should you use the hose clamps on barbed fittings, please note that the fittings will widen the outer diameter of the tubing by 1-2mm (depending on the wall thickness)

Model: TR-68248-4P

Conclusion

By our suggestions above, we hope that you can found phobya water cooling for you.Please don’t forget to share your experience by comment in this post. Thank you!